If you searched for nissan silverado oil capacity in quarts, you're probably standing in your driveway with an oil jug in one hand and a dipstick in the other. Here's the important detail up front: the Silverado is manufactured by Chevrolet, not Nissan. No vehicle called the "Nissan Silverado" exists in any market. This mix-up is surprisingly common online, and it can lead to using the wrong oil amount which risks engine damage. Below, you'll find the correct oil capacity in quarts for the Chevrolet Silverado across all major engine options, plus guidance on how to avoid the most common mistakes.

Is There Really a Nissan Silverado?

No. The Silverado nameplate belongs to General Motors and has been a Chevrolet truck since 1999. Nissan's full-size pickup is the Titan, and their midsize truck is the Frontier. If you own a Nissan truck and landed on this page, scroll down I've included Nissan oil capacities too. If you actually drive a Chevy Silverado, the next section is what you need.

What Is the Oil Capacity for a Chevrolet Silverado?

Silverado oil capacity in quarts depends entirely on the engine size and model year. Using the right amount prevents overfilling (which foams the oil) and underfilling (which starves the engine of lubrication). Here are the most common configurations:

Chevrolet Silverado 1500 Oil Capacity

  • 4.3L V6 (LV3): 6 quarts with filter
  • 4.8L V8 (L20, older models): 6 quarts with filter
  • 5.3L V8 (L83/L84/LM7/L33): 8 quarts with filter (some older 5.3L engines use 6 quarts always verify)
  • 6.0L V8 (L96/LFA, older models): 6 quarts with filter
  • 6.2L V8 (L87/L86): 8 quarts with filter
  • 2.7L Turbo I4 (L3B): 6 quarts with filter
  • 3.0L Duramax Diesel (LM2/LZ0): 7 quarts with filter

Chevrolet Silverado 2500HD / 3500HD Oil Capacity

  • 6.6L V8 Gas (L8T): 8 quarts with filter
  • 6.6L Duramax Diesel (L5P): 10 quarts with filter

Always confirm with your owner's manual before adding oil. A VIN lookup on the GM owner center website will also show your exact engine code.

What If You Actually Own a Nissan Truck?

If your truck says Nissan on the badge, here are the correct oil capacities:

  • Nissan Titan 5.6L V8 (Endurance/VK56): ~7 quarts with filter
  • Nissan Frontier 4.0L V6 (VQ40): ~5.4 quarts with filter
  • Nissan Frontier 2.5L I4 (QR25): ~4.8 quarts with filter
  • Nissan Frontier 3.8L V6 (VQ38, 2020+): ~5.1 quarts with filter
  • Nissan Navara 2.3L Diesel (YS23): ~6.5 quarts with filter

Why Does Getting the Exact Oil Capacity Matter?

Engines are engineered to run with a specific volume of oil. Even one extra quart can raise oil pressure enough to blow seals. Running a quart low during hard acceleration can drop oil pressure and damage bearings. When you're doing your own oil change, you need to know the exact quarts with filter not a guess.

Common Mistakes People Make With Oil Capacity

  • Trusting generic charts without checking engine code. The same Silverado model name can have four or five different engines across generations.
  • Not accounting for the oil filter. Capacity specs are usually listed "with filter" if you don't swap the filter, you'd overfill by roughly half a quart.
  • Pouring in the full amount right away. Always add about 0.5 quarts less than listed, run the engine for a minute, shut it off, wait, then check the dipstick and top off as needed.
  • Confusing dry fill with service fill. A brand-new or rebuilt engine may need more oil than a routine drain-and-fill.

How to Check You Have the Right Amount After Filling

  1. Start the engine and let it idle for 60–90 seconds so oil circulates through the filter and passages.
  2. Shut the engine off and wait at least 5 minutes (10 minutes on newer Silverados with deeper oil pans).
  3. Pull the dipstick, wipe it clean, reinsert fully, then pull it again to read.
  4. The oil level should sit between the two marks ideally closer to the upper mark without exceeding it.

What About Oil Type and Viscosity?

Capacity alone isn't enough. Using the wrong viscosity can cause the same problems as the wrong quantity. Most Silverado engines call for 0W-20 or 5W-30 full synthetic. You can read more about the recommended oil type and viscosity to match your specific engine.

Do You Need to Know the Drain Plug Size Too?When you're under the truck ready to drain, having the right socket saves you from rounding off the plug. The drain plug size and torque spec vary by generation, so check the drain plug size and torque specifications before you start.

Full Oil Change Steps for a Silverado

Once you know the capacity, oil type, and plug size, you're ready for the job. A complete walkthrough with torque values and tool list is available in the step-by-step oil change instructions.

For a quick visual reference on oil viscosity ratings, you can check the SAE Oil Viscosity Chart from Creative Fabrica.

Quick-Reference Checklist Before Your Next Oil Change

  • ✅ Confirm your exact engine code (check the underhood sticker or owner's manual)
  • ✅ Note the oil capacity in quarts with filter
  • ✅ Buy the correct viscosity don't guess between 0W-20 and 5W-30
  • ✅ Get the right drain plug socket size before you crawl under the truck
  • ✅ Add ~0.5 quarts less than spec, start the engine, then check the dipstick and top off
  • ✅ Dispose of used oil at an auto parts store or recycling center never pour it down a drain

Tip: Write your oil capacity and type on a small sticker inside your glove box door. It eliminates the lookup every 5,000–7,500 miles and keeps you from second-guessing at the auto parts store shelf.